| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
net: ethernet: cortina: Fix budget accounting
The gmac_rx() function returns the remaining NAPI budget, but its
caller treats the return value as the number of packets received. An
idle poll therefore reports a full budget and remains scheduled.
Return the number of received packets instead. Preserve the existing
free queue refill accounting by adding that count directly; continuing
to subtract it from the budget would invert the refill behavior. |
| pypdf is a free and open-source pure-python PDF library. Prior to 6.18.1, a crafted PDF containing a partially malformed /FlateDecode stream with padded data can force pypdf/filters.py to use inefficient byte-by-byte decompression while the earlier recovery counter fails to advance for bytes that successfully decode, causing long runtimes and application unavailability. This is a residual issue after the malformed FlateDecode recovery fix. This issue is fixed in version 6.18.1. |
| `_nx_icmpv6_validate_options()` scans the option area with `while (length > 2)` (`common/src/nx_icmpv6_validate_options.c:79`). An area whose size leaves a one- or two-byte residue exits the loop with that tail unexamined; the residue is not negative, so the function returns `NX_SUCCESS`. Its zero-length rejection never sees those bytes.
Every consumer then re-walks the same area, reading a two-byte option header at the residue and subtracting `nx_icmpv6_option_length << 3` with no zero check and no remaining-length check. Three outcomes follow, selected by bytes the attacker controls.
**Zero length byte.** The walker subtracts zero and advances zero. All four handlers loop forever — `_nx_icmpv6_process_ra` (`nx_icmpv6_process_ra.c:245, :528`), `_nx_icmpv6_process_ns` (`:251, :329`), `_nx_icmpv6_process_na` (`:147, :156`) and `_nx_icmpv6_process_redirect` (`:247, :350`). The walk runs in the IP thread, which is the highest-priority thread and does not yield inside the loop, so the system stops until a watchdog reset and the frame can be replayed after each one.
**Non-zero length byte on a short residue.** The three unsigned counters underflow — `2 - 8` becomes `0xFFFFFFFA` — and the walk continues past the packet buffer, reading until it faults or meets a zero length byte and freezes. The Router Advertisement counter is signed and exits cleanly in this case.
**One-byte residue.** The walker reads a two-byte option header, over-reading one byte.
During a runaway walk, stray bytes parsing as a link-layer address option are copied into the neighbor cache (`nx_icmpv6_process_ns.c:280, :293`) and subsequently used as the destination MAC for frames to that neighbour, placing off-packet memory on the link. Confirmed by inspection, not reproduced. |
| Unbounded PPP IPCP Option Parsing Causes a Worker Stall and Out-of-bounds Read |
| iperf3 versions prior to 3.22 contains a denial of service vulnerability that allows unauthenticated remote attackers to crash-loop the server's UDP receive worker into an unrecoverable infinite loop by sending a single crafted control-channel parameter message followed by one 16-byte UDP datagram. Attackers can permanently pin the affected per-stream receive thread at approximately 100% CPU usage, rendering the server unusable until forcibly killed with SIGKILL, as the process does not respond to normal control-channel closure. |
| Improper output encoding in DevTools in Google Chrome prior to 154.0.8037.57 allowed a remote attacker who had compromised the renderer process to potentially execute arbitrary code outside the sandbox via a crafted HTML page. (Chromium security severity: High) |
| A vulnerability was detected in GraphicsMagick up to 1.3.47. Affected by this vulnerability is the function ExtractPostscript of the file coders/wpg.c of the component WPG File Handler. Performing a manipulation results in uncontrolled recursion. The attack may be initiated remotely. The patch is named 627b5b1b2fc2. It is suggested to install a patch to address this issue. The vendor was contacted early, responded in a very professional manner and quickly released a fixed version of the affected product. |
| In the Linux kernel, the following vulnerability has been resolved:
net/sched: drr: clamp quantum in change class
drr_change_class() rejects explicit quantum==0 but falls back to
psched_mtu() with no floor. With a crafted size table qdisc_pkt_len
reaches ~2 GiB, so quantum=1 (or a zero psched_mtu on a headerless
device) makes the deficit-refill loop spin under the qdisc lock.
Add clamp_t(u32, quantum, 256, 1<<20) after the zero reject and on the
fallback path. The explicit-zero reject is preserved.
Conditions to recreate the bug:
CONFIG_NET_SCH_DRR=y. Requires CAP_NET_ADMIN (namespace-local via
unshare -Urn suffices).
tc qdisc add dev dummy0 root drr
tc class add dev dummy0 parent 1: classid 1:1 drr quantum 1 |
| Improper Verification of Source of a Communication Channel in the ADS discovery of the Go implementation of Apache PLC4X (PLC4Go) allows an attacker able to send UDP datagrams to the discovering host to redirect subsequent connections to an arbitrary, attacker-chosen address. The discovery result's connection
address was derived from the AmsNetId claimed in the response body rather than from the datagram's actual source address. One spoofed discovery response can therefore insert an inventory entry pointing at any host, including hosts outside the local network, and an application that connects to discovered devices
will open its ADS session, including any configured route credentials, to that host.
Additionally, discovery listeners in both implementations can be disabled by a single malformed datagram:
- In PLC4Go ADS discovery, a short version block causes a panic that ends the listener for the rest of the discovery call, so legitimate devices answering afterwards are not reported.
- In PLC4J, the ADS and EtherNet/IP discoverers stop on an unhandled exception from a malformed response.
- The PLC4J Modbus discoverer can be made to spin indefinitely, consuming a CPU core, by a scanned host that sends a partial response.
Exploitation requires the application to invoke the discovery API, which is opt-in, and for the connection redirect, to act on the discovered items.
This issue affects Apache PLC4X: PLC4Go from 0.11.0 before 1.0.0; PLC4J ADS and Modbus drivers from 0.10.0 before 1.0.0; PLC4J EtherNet/IP driver from 0.11.0 before 1.0.0. PLC4Go is consumed as the Go module github.com/apache/plc4x/plc4go; versions refer to the corresponding Apache PLC4X releases.
Users are recommended to upgrade to version 1.0.0, which fixes the issue. Version 1.0.0 derives the connection address from the datagram's source address and logs a warning when the claimed AmsNetId disagrees with it. |
| USB HID protocol dissector infinite loop and memory leak in 4.6.0 to 4.6.8 and 4.4.0 to 4.4.18 allows denial of service |
| In the Linux kernel, the following vulnerability has been resolved:
drm/pagemap: Prevent double migration of device pages
A device-private folio migrated to system memory by a CPU fault can
remain reachable through the raw-PFN eviction path until migration
finalization drops the source reference.
If eviction selects the same device-private folio during this window,
it can attempt to migrate the folio again. The second migration can leave
an uncharged folio on an LRU list, causing folio_lruvec_lock_irqsave() to
retry indefinitely and resulting in a soft lockup and RCU stall.
Mark successfully migrated device-private folios using a low bit of
their zone_device_data before migration finalization. Make both CPU-fault
and raw-PFN migration paths skip device-private folios carrying this
flag.
Mask the flag when retrieving the drm_pagemap_zdd pointer and preserve
it when a device-private folio is split. Keeping the state on the physical
folio also avoids depending on a virtual address that may change before a
fault occurs.
v2:
- Replace the retired-PFN XArray with an embedded bitmap. (Matthew Brost)
- Mark every base page covered by a migrated folio so retirement remains
valid if the folio is later split.
v3:
- Store the migrated state in a low bit of zone_device_data instead of
adding virtual-range and bitmap tracking to the ZDD. (Matthew Brost)
- Mask the flag when retrieving the ZDD and preserve it when splitting
a folio.
- Drop the pre-existing fixes already covered by Matthew Brost's series:
https://patchwork.freedesktop.org/series/171651/
v4:
- Advance by the folio size only for migration entries marked with
MIGRATE_PFN_COMPOUND. (Sashiko)
v5:
- Simplify ZDD flag updates and folio iteration. (Matthew Brost)
- Skip retired device-private folios in the CPU-fault path. (Matthew Brost)
- Preserve flag bits while taking a new ZDD reference for split folios.
v6:
- Restore MIGRATE_PFN_COMPOUND-aware stepping so non-compound migration
entries are processed one at a time. (Sashiko)
- Drop the pre-existing fixes already covered by Matthew Brost's series:
https://patchwork.freedesktop.org/series/171651/
The lockup was observed as:
[10109.860465] watchdog: BUG: soft lockup - CPU#9 stuck for 26s! [kworker/u65:5:6557]
[10109.860524] Tainted: [S]=CPU_OUT_OF_SPEC, [O]=OOT_MODULE
[10109.860524] Hardware name: ASUS System Product Name/PRIME Z790-P WIFI, BIOS 0812 02/24/2023
[10109.860525] Workqueue: xe_page_fault_work_queue xe_pagefault_queue_work [xe]
[10109.860644] RIP: 0010:_raw_spin_unlock_irqrestore+0x57/0x80
[10109.860655] Call Trace:
[10109.860655] <TASK>
[10109.860657] folio_lruvec_lock_irqsave+0x216/0x220
[10109.860661] ? __pfx_lru_add+0x10/0x10
[10109.860665] folio_batch_move_lru+0xc8/0x450
[10109.860670] ? lock_acquire+0xc4/0x2d0
[10109.860674] ? __folio_batch_add_and_move+0x60/0x2e0
[10109.860677] ? folio_migrate_mapping+0xa6/0x110
[10109.860679] ? folio_migrate_flags+0x13b/0x1b0
[10109.860681] ? __pfx_lru_add+0x10/0x10
[10109.860683] __folio_batch_add_and_move+0xe7/0x2e0
[10109.860685] ? dma_iova_try_alloc+0xb0/0x140
[10109.860689] folio_add_lru+0x64/0x80
[10109.860691] __migrate_device_finalize+0x12c/0x270
[10109.860695] migrate_device_finalize+0x10/0x20
[10109.860698] drm_pagemap_evict_to_ram+0x185/0x370 [drm_gpusvm_helper]
[10109.860704] ? drm_pagemap_evict_to_ram+0x96/0x370 [drm_gpusvm_helper]
[10109.860709] xe_svm_bo_evict+0x15/0x20 [xe]
[10109.860819] ? xe_svm_bo_evict+0x15/0x20 [xe]
[10109.860921] xe_bo_move+0x107e/0x1570 [xe]
[10109.860992] ? xe_ttm_tt_create+0x168/0x340 [xe]
[10109.861059] ? __up_read+0x98/0x2b0
[10109.861061] ? lock_is_held_type+0xa3/0x130
[10109.861067] ttm_bo_handle_move_mem+0xe8/0x1e0 [ttm]
[10109.861075] ttm_bo_evict+0x141/0x1c0 [ttm]
[10109.861081] ttm_bo_evict_cb+0x9f/0x100 [ttm]
[10109.861086] ttm_lru_walk_for_evict+0x84/0x190 [ttm]
[10109.861091] ? xe_ttm_vram_mgr_new+0x258/0x3a0 [xe]
[10109.861198] ttm_bo_alloc_resource+0x219/0
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
sctp: fix soft lockup from unpadded ASCONF-ACK parameter iteration
sctp_verify_asconf() walks ASCONF-ACK parameters with
sctp_walk_params(), which advances by SCTP_PAD4(length), while the
consumer sctp_get_asconf_response() iterates the same parameters
advancing by the raw length, without padding. A single odd-length
parameter desynchronises the two walks and makes the consumer
interpret attacker-controlled bytes at a misaligned offset.
When those bytes yield a length of zero, the while loop over
asconf_ack_len makes no progress, spinning forever in softirq
context, and the watchdog reports a soft lockup. All reads stay
within the received skb, so the lockup is a pure remote denial of
service. A remote peer can trigger it with a crafted ASCONF-ACK on
an ADD-IP enabled association with an outstanding ASCONF (RFC 5061
section 4.1.2 requires the chunk to be authenticated, but the
predefined empty key id 0 allows the peer to compute the same
association HMAC from publicly exchanged parameters, so the gate
does not help).
The SCTP_PARAM_ERR_CAUSE case of sctp_verify_asconf() also performs
no length check, letting a parameter without a complete error
header reach the consumer, which reads errhdr.cause past the end of
the parameter, an out-of-bounds read.
Reject SCTP_PARAM_ERR_CAUSE parameters shorter than
sizeof(struct sctp_addip_param) + sizeof(struct sctp_errhdr) at the
verifier, and advance the consumer iterator with the same padding
rule as the verifier to keep the two walks in lockstep. The verifier
change guarantees a complete error header in every ERR_CAUSE
parameter the consumer can see, so the consumer's asconf_ack_len
check is dropped and it returns err_param->cause directly. The
consumer padding fix is still required because odd lengths remain
valid for SCTP_PARAM_ERR_CAUSE per RFC 5061.
The issue was found by ZeroHive, a vulnerability hunting agent at
Tencent Yunding Lab. |
| Zammad is a web based open source helpdesk/customer support system. Prior to 7.1.2, a user with Knowledge Base editing rights for a category can embed a video widget in a published answer with a specially crafted value. When the answer is rendered, that value is inserted into the page's HTML without being escaped for its attribute context, allowing it to break out and inject additional HTML into the page. When another user who has permission to switch between user sessions views the affected answer, the injected HTML causes their browser to silently send a request to Zammad's session-switching endpoint using their own active credentials. This results in switching their session to an account chosen by the person who wrote the Knowledge Base answer. No action is required from the viewer beyond opening the published answer. This issue is fixed in version 7.1.2. |
| In the Linux kernel, the following vulnerability has been resolved:
xfs: don't spin forever on zero-length dirents when salvaging them
LOLLM noticed that xrep_dir_recover_data can spin forever if it
encounters an unused dirent that claims to have length zero. Fix that,
and prevent the same thing from happening with a zero-length entry. |
| urllib3 is an HTTP client library for Python. From 2.6.2 until 2.8.0, HTTPResponse.stream and HTTPResponse.read_chunked can enter an infinite loop because the Deflate decoder retains trailing bytes as unconsumed input after reaching end-of-stream and repeatedly decodes them without progress. The issue occurs when an untrusted server sends a chunked Deflate response whose decoded body exceeds a positive finite chunk size and whose encoded body has trailing bytes, specifically a response with Transfer-Encoding: chunked and Content-Encoding: deflate, content decoding enabled, and the positive finite amt=N streaming chunk size. The attack mechanism is that a malicious server returns a compressed chunked response with trailing bytes after the Deflate stream. The impact is excessive CPU usage and a request that does not complete, and network read timeouts do not interrupt the loop because no further socket read occurs. This issue is fixed in version 2.8.0. |
| TIFF protocol dissector infinite loop in 4.6.0 to 4.6.8 and 4.4.0 to 4.4.18 allows denial of service |
| TTL file parser infinite loop in 4.6.0 to 4.6.8 allows denial of service |
| Pod::Text versions before 6.1.1 for Perl allow CPU and memory exhaustion formatting a POD document whose =over nesting drives the margin to the output width.
Each =over adds its indent to the margin, which wrap() subtracts from the output width to get the space available for text. When that space reaches zero, the line-splitting substitution matches the empty string, and the loop consumes no input while appending the margin padding on every pass.
Formatting an attacker-supplied POD document never returns, and the output grows until memory is exhausted. |
| Net::IDN::Punycode versions before 2.590 for Perl hang, crash or return a wrong label via unvalidated malformed UTF-8 in encode_punycode.
Neither backend checks that its input is well-formed UTF-8, so a string with the UTF-8 flag set over malformed bytes, as the :utf8 PerlIO layer produces from any malformed input, reaches the encoder unchecked. On perl 5.32 and later the XS backend reports a malformed sequence with a length of `(STRLEN)-1`, so the scan steps back one byte instead of forward and never ends. On earlier perls the XS returns a valid label for a different name. The pure-Perl backend runs a regex over the flagged string. Depending on the bytes, it aborts with SIGBUS on perl 5.28 and later, dies with a panic, or returns a wrong label.
The documented conversion functions match the label against Unicode properties first and that match dies on such a string, so only a direct call to encode_punycode reaches the defect. The decoder is not affected.
A direct caller encoding attacker-supplied bytes hangs, crashes or gets a label for a name the input never held. |
| js-yaml is a JavaScript YAML parser and dumper. From 3.0.0 until 3.15.2, 4.3.2, and 5.4.1, maxTotalMergeKeys in lib/js-yaml/loader.js and lib/loader.js does not count empty mapping sources while processing the merge key <<. An attacker can alias a large sequence of empty mappings into many merge targets, causing O(N * K) processing while totalMergeKeys remains unchanged and the configured resource limit is never reached. A relatively small YAML document can therefore cause prolonged CPU consumption in applications that parse untrusted YAML, and merge processing is enabled by default on these release lines. In v3 & v4, merge is enabled by default so the severity score is higher. This issue is fixed in versions 3.15.2, 4.3.2, and 5.4.1. |
